Victor Data Systems XID Manual de Instruções

Jam (TurnOver)Jam (Hopper)HR is too hot.Please removeMEDIA FILMPlease,Power Off.>Ink>>Cleaning>Counter Reset>Display>ReadyMENUInstru

10Set-upConnecting with a host computerThis section describes the settings for connection witha host computer.Make sure that the power switch isswitch

11(to the next page)3.Connect the printer and IC unit.Connect the cable which comes with the IC unit to theOPTION 1 terminal.4.Connect the IC unit wit

12Set-up (continued)Compact IC unit (sold separately)Please ask your dealer for the Compact IC unitconnection.1.Connect the compact IC unit to the hos

13(to the next page)Card dischargeslotClawCard stacker(accessory)Card stackerreceptacleInstalling the card stacker1.Mount the card stacker on the prin

143.Insert the ink ribbon into the cassette.Stretch the ink ribbon along four shafts with the ink faceof the ribbon facing outside and insert the bobb

15(to the next page)5.Insert the cassette along the guide rail.Insert the cassette until it clicks securely into position.The lever returns to its ori

16Set-up (continued)Setting the retransfer filmDo not touch the retransfer filmsurface with your hands.1.Activate the slide knob and open the printerd

17(to the next page)4.Wind the retransfer film to take up the slack.Turn the knob in the arrow direction to wind a smallportion of the retransfer film

18Set-up (continued)Setting cardsPlease use cards specified by your dealer. This unitcan take both 0.76 mm-thick and 0.25 mm-thickcards. The factory s

19(to the next page)3.Close the card tray.Push the card tray back into the printer until it no longermoves.MemoTo print pre-printed cards on this prin

2Declaration of ConformityModel Number: XID Printeryyyyy(y=A-Z,0-9 or blank)Product name: Card PrinterWe herewith declare that the above mentioned pro

20Set-up (continued)Loading cardsLoad cards when the printer’s LCD shows the message“Ready” or “No Card”, and not when printer operationshave stopped

21Before useNames of parts on the operationpanelSetting buttonsInitializes the printer by thesoftware when an error occurs oran error is cancelled.The

22Operation display LED contentsand the LCD panelFor details, see p. 40 – 42 of this manual.Initialization periodWhen the power is turned on, the prin

23OperationTurning on the power1.Before turning on the power, check thefollowing:Make sure that the printer door is completelyclosed.Make sure that th

24Be sure NOT to do any of the following during printingoperations:vDo not open the printer door.vDo not open the card tray.(while the LCD panel displ

25Operation (continued)User modesThe settings for printing media, card, etc. can bemade in the User mode.Press the MENU button when the unitis in the

26User mode settings>Bend Remedy>>Retransfer>>>Media Type>>Temp. Level>>Speed (Front)>>Speed (Back)Standard:00(Sta

27>Display>>>Counter>>Contrast>>Back ColorTotal-2BLUEENTERENTERENTERMENUMENUMENUEXITEXITEXITENTEREXITSKY BLUE, BLUE, LIGHT BLU

28Clearing the free counterReset the free counter.The [Total] counter and [Head] counter cannot bereset.Cleaning modeThe printer is provided with an o

29Operation (continued)Ink mode settingChange settings according to the ink ribbon used.>Ink>>>Black Level>>Black Mode>>Ink Ty

3For USA onlyNOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to Part 15 of the FCC Rule

30Retransfer mode setting>Retransfer>>>Media Type>>Temp.LevelStd(1000/roll):00(Standard)-2ENTERENTERENTERENTERRESETENTERMENUMENUMENU

31Operation (continued)Buzzer mode settingThe buzzer indicating errors can be turned on oroff.Power saving mode settingsThe printer enters into the po

32Setting the bend remedy modeSingle-sided printing may cause a bend depending onthe cards. Adjust the setting to get rid of the bend.CAUTION>Bend

33Operation (continued)Card size setting modeThe printer is designed to load two sizes of cards.Set the card size according to the card to be printed.

34Care and cleaningAlways make sure that the unit is turned off before cleaning.(However, cleaning of the discharge rollers and magnetic head should b

35Cleaning the fan filterWhen the fan filter gets dirty, partial omissions mayoccur on the printed cards, or the printing resultlooks dirty. It is rec

36Side filterPress down the sponge intothe dents at four corners, andset it under the tabs on theframe.Bottom filterPlace the spongeunder the tabs on

37Cleaning the card feed rollers andheat rollersDirty rollers are the major cause of jamming of thecards. It is recommended to clean the rollers oncea

38Cleaning the magnetic headDirty magnetic head will cause a write/read error. Itis recommended to clean the magnetic head afterprinting about 1,000 c

39Jam (TurnOver)Jam (Hopper)Jam (Transfer)TroubleshootingLayout of rollers inside the printerBelow is a diagram of the layout of rollers inside the pr

4ContentsBefore use... 7Product features ... 7Checki

40Error code listingThe meaning of “reset → enter buttons” in the list is,after pressing the Reset button, press the Enter buttonto initialize the uni

41Troubleshooting (continued)Should your printer require servicing, turn it off and unplug it and make inquiries at theoutlet where it was purchased.T

42EXT2 ComminucateError code Description of error RemedyExternal unit2 communicationserrorTurn the power off and then on again. Call for service if th

43Troubleshooting (continued)Removing card jamsTo determine the part of the machine affected by acard jam refer to the error code on the operationpane

44Turnover section [Jam (turnover)]1.Open the printer door and remove the inkribbon cassette.See p.14 in this manual.2.Remove any jammed cards.Retrans

45SpecificationsMain specificationsRecording method : Sublimation type retransferFeed format : Automatic feedRecording density : 300 dpiExpression gra

46External appearance and dimensions Front viewSide viewunit/mm343347381

47MEMO

C 2003 VICTOR DATA SYSTEMS Co.,Ltd.Distributor: Digital Identification Solutions GmbH Teckstrasse 52 D - 73734 Essl

5(to the next page)Notes for safe operationBefore you useRead these notes on safety thoroughly before operating your printer in order to use the unit

6Notes for safe operation (continued)mPull out the power plug before cleaning themachine.•This is for preventing electric shocks.mPull out the power p

7(to the next page)Before useProduct featuresvThis card printer allows printing of high-quality, full-color images equivalent to photographic quality

8Before use (continued)Storing and handling cards after printingAvoid storing the cards in locations exposed to directsunlight or with high humidity.F

9Names of partsFront When the printer door is openSlide knobControl panelPrinterdoorCard trayPower switchRetransfer film cassette(Accessory)Ink ribbon